Valid NACE-CIP1-001 Exam Dumps Ensure you a HIGH SCORE (2025)
Pass NACE-CIP1-001 Exam with Latest Questions
NEW QUESTION # 33
Removal of welds splatter is required:
- A. When NACE/SSPC abrasive blast standards are specified
- B. When ISO abrasive blast standards are specified
- C. On every job
- D. When specifically identified in the owner's specification
Answer: D
NEW QUESTION # 34
Due to a previous premature coating failure the owner has required the original coating applicator to return to remove and replace 10,000 square feet of a failed three coat system at the applicator's cost. Due to the financial implications of another failure, the owner has offered you the job as the NACE CIP Level 1 Coating Inspector and explained that he expects you to be his "insurance policy" for this job. You have never been involved in a warranty job before and are unfamiliar with the coating system.
Your preferred FIRST course of action is to:
- A. Review the Product Data Sheets, and conduct a walk thru of the job site prior to the pre-job Conference
- B. Purchase Professional Liability Insurance prior to job commencement
- C. Review the Product Data Sheets and meet with the Coating Applicator 'prior to the pre-job meeting
- D. Meet with the owner and explain your limitations and concerns prior accepting the assignment
Answer: A
NEW QUESTION # 35
NACE No. 4/SSPC-SP-7 is a joint standard for
- A. white metal blast cleaning.
- B. commercial blast cleaning.
- C. brush-off blast cleaning.
- D. near-white metal blast cleaning.
Answer: C
NEW QUESTION # 36
What is the minimum spot measurement value allowed by SSPC-PA 2 in each 10 m2 (100 ft2) area?
- A. 100% of the specified maximum thickness
- B. 80% of the specified minimum thickness
- C. 90% of the specified maximum thickness
- D. 70% of the specified maximum thickness
Answer: B
NEW QUESTION # 37
A NACE Coating Inspector is permitted to transport coating material when:
- A. Asked to do so by the Owner's Representative
- B. Asked to do so by the Coating Application team
- C. If the Inspector meets all the necessary requirements for Transportation of Dangerous Goods
- D. The Inspector should never transport coating material
Answer: D
NEW QUESTION # 38
According to SSPC PA 2 a Spot Measurement is:
- A. The overall average of all readings
- B. The average of gauge readings taken in a 4cm (1.5 inch) circle
- C. A single gauge reading
- D. The average of all spot measurements in a given area
Answer: B
NEW QUESTION # 39
What is the minimum recommended distance away from an edge that an inspector should take a measurement with a dial-type magnetic pull-off Dry Film Thickness (DFT) gauge?
- A. 2.5 cm (1 inch)
- B. 6.35 cm (2.5 inch)
- C. 2.5 millimeters (.10 inch)
- D. 1 cm (.39 inch)
Answer: A
NEW QUESTION # 40
Daily reports are important because:
Select All That Apply
- A. Inspectors rarely change on a project.
- B. the information impacts future projects.
- C. Management uses them to make personnel decisions.
- D. The information aids communication with supervisors.
Answer: B,C,D
NEW QUESTION # 41
If inspectors identify issues of non-conformance during an inspection, they should
- A. inform both the Contractor and the inspector's supervisor so they can take appropriate corrective actions
- B. perform additional tests secretly to ensure there are no other potential issues at the site
- C. instruct the contractor's personnel in how to correct the issue so the project is not delayed
- D. wait until the final report is being prepared to identify the issues in writing so they are fully documented
Answer: A
NEW QUESTION # 42
You are an inspector on a project where SSPC SP 3 is specified.
What sort of tools should you expect the Contractor to use to achieve the standard?
- A. Hand tools
- B. Power tools
- C. Abrasive blast nozzles
- D. Airless spray equipment
Answer: B
NEW QUESTION # 43
Safety Data Sheets must be carefully reviewed by:
- A. The Inspection personnel
- B. The Application personnel
- C. The Owner's personnel
- D. All personnel involved in the job
Answer: D
NEW QUESTION # 44
Common errors that may produce inaccurate readings when using a Dial-Type Magnetic Pull-Off Dry Filth Thickness (DFT) gauge include:
Select All That Apply
- A. Rotating the dial too fast when taking measurements
- B. Failing to determine the base metal reading (BMR)
- C. Measuring ditty, tacky, or soft films
- D. Taking measurements too far from the edge of a surface
Answer: A,B,C
NEW QUESTION # 45
How many gauge readings does SSPC-PA 2 require within a 4 cm (1.5 inch) diameter circle?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: C
NEW QUESTION # 46
Excessive working of the surface with a power grinder can be detrimental because excessive burnishing
- A. damages structural elements thereby speeding up the corrosion process.
- B. develops a polished surface, which is a poor anchor profile for most coatings
- C. scratches the surface too deeply resulting in uneven coating application
- D. develops a good anchor profile resulting in uneven coating application.
Answer: B
NEW QUESTION # 47
Check abrasive blast pressure close to the
- A. blast nozzle
- B. substrate
- C. compressor
- D. blast pot
Answer: A
NEW QUESTION # 48
Stripe coats are best applied by:
- A. Brush
- B. Airless spray
- C. Conventional spray
- D. High volume low pressure spray
Answer: A
NEW QUESTION # 49
On a blast-cleaned surface, Ian ultraviolet light is generally used to detect
- A. sulfates
- B. grease and oil
- C. inhibitor residues
- D. soluble chemical salts
Answer: B
NEW QUESTION # 50
......
NACE-CIP1-001 Exam Practice Questions prepared by NACE Professionals: https://vcecollection.trainingdumps.com/NACE-CIP1-001-valid-vce-dumps.html
