Get Instant Access of 100% REAL NACE-CIP2-001 DUMP Pass Your Exam Easily
NACE-CIP2-001 Free Exam Questions with Quality Guaranteed
NACE-CIP2-001 certification exam is recognized as a benchmark for excellence in the coating inspection industry. Coating Inspector Level 2 certification is highly valued by employers and clients alike, as it demonstrates that the individual has the knowledge, skills, and abilities required to perform quality inspections of coatings. Coating Inspector Level 2 certification also provides individuals with a competitive edge in the job market, as it sets them apart from others who do not have the certification.
NEW QUESTION # 19
You are the NACE Level 2 Inspector on a project where overcoating of galvanized steel is being performed. The specification references SSPC SP 16 as the surface preparation method. At the pre-job meeting operations personnel make it clear that abrasive blasting will not permitted. The Owner's representative asks you what other methods might be used.
Of the options shown below, what would be the preferred option in this situation?
- A. SP 1 followed by SP 2
- B. SP 1 followed by caustic etching
- C. SP 1 followed by acid etching
- D. SP 1 followed by SP 3
Answer: A
NEW QUESTION # 20
Which standards are generally established by private-sector bodies and are available for use by any person or Organization, private or government?
- A. Mandatory
- B. De facto
- C. Consensus
- D. Voluntary
Answer: D
NEW QUESTION # 21
Because a NACE Level 2 Inspector has been trained in specific destructive tests, it is up to the Inspector to decide if and when a destructive test is required.
- A. False
- B. True
Answer: A
NEW QUESTION # 22
When performing an adhesion test in accordance with ASTM D 3359 where the Dry Film Thickness is approximately 10 mils, the Inspector should use:
- A. Method B - Cross Hatch
- B. Method B - X cut
- C. Method A - Cross Hatch
- D. Method A - X Cut
Answer: D
NEW QUESTION # 23
When ASIN D 3363 is specified the Inspector must:
- A. Record the two end points identified in the standard
- B. Record the percentage of failure
- C. Use the correct solvent
- D. Record the highest value attained
Answer: A
NEW QUESTION # 24
Non-Conformance Reports are designed to:
- A. Punish the Contractor for substandard work
- B. Assist the Owner in negotiating credits from the Contractor
- C. To identify items that do not meet the specification requirements
- D. Elevate the status of the Inspector
Answer: C
NEW QUESTION # 25
When performing a hardness test on a coating which has elastic properties the inspector is likely to likely to observe:
- A. No difference from any other coating
- B. A very high reading
- C. Cold flow or creep
- D. A very low reading
Answer: C
NEW QUESTION # 26
Ideally, documentation requirements should be defined:
- A. By the contractor
- B. By the inspector
- C. At the pre-job conference
- D. In the specification
Answer: D
NEW QUESTION # 27
The cost of qualified Coating Inspection is normally offset by:
- A. Lower Coating Life Cycle Costs
- B. Lower Supervision Costs
- C. Lower Application Costs
- D. Lower Safety Enforcement Costs
Answer: A
NEW QUESTION # 28
Surface preparation of concrete is performed using:
- A. Methods that are completely different to steel
- B. Methods that have been modified for concrete
- C. Methods that are exactly the same as steel
- D. Methods that are the same as wood
Answer: B
NEW QUESTION # 29
The coating applicator has ignored a enface preparation hold point and applied coating over the surface without a sign off from you as the inspector.
Your FIRST preferred course of action is to:
- A. Advise the Owner and write a Non-Conformance report
- B. Ignore the situation
- C. Stop the job
- D. Require the Applicator to remove the coating
Answer: D
NEW QUESTION # 30
A failure caused by applying a coating too thinly is known as
- A. chalking.
- B. failure to cure.
- C. cracking.
- D. pinholes.
Answer: D
NEW QUESTION # 31
Individuals conducting Coating Surveys should:
- A. Always be trained and experienced Coating Industry
- B. Always be experienced Specification Writers
- C. Always be NACE or SSPC Protective coating Specialists
- D. Always be NACE Level 3 Certified Inspectors
Answer: A
NEW QUESTION # 32
You are a NACE Level 2 Coating Inspector who has just arrived on a job in progress where there is no Inspection and Test Plan (ITP). The first morning you arrive the job is behind schedule and you are asked to take DIY Film Thickness readings.
Your FIRST preferred course of action is to:
- A. Refuse to take readings until an is in place
- B. Call your supervisor
- C. Develop your own methodology and proceed take the readings
- D. Use a generally accepted industry standard and to take readings
Answer: D
NEW QUESTION # 33
You should bulk store coatings containing isocyanates
- A. in a heated warehouse.
- B. in a well ventilated area separate from the work place.
- C. wherever it is convenient
- D. in a refrigerated warehouses
Answer: B
NEW QUESTION # 34
Generally for safety considerations, waterjetting hose connections use
- A. a whip-lock device.
- B. a long wand.
- C. an oil/water separator.
- D. filters.
Answer: A
NEW QUESTION # 35
You are the new NACE Level 2 Inspector on a job which had been very problematic. The previous Inspector was fired duo to personality conflicts with the Contractor's supervisor. Upon arriving onsite the Contractor's supervisor advises you in no uncertain terms that you will be the next to go, unless you cooperate with him.
Your FIRST preferred course of action is to:
- A. Defend the previous inspector
- B. Express a willingness to work with the site team and follow the specification
- C. Suggest to the Owner that the supervisor should be removed from site
- D. Challenge the supervisor's authority
Answer: B
NEW QUESTION # 36
When observing fabrication defects the NACE Inspector should:
- A. Stop the job immediately
- B. Require they be corrected prior to coating
- C. Write an NCR and call the fabricator
- D. Consult the specification to determine how they should be treated
Answer: D
NEW QUESTION # 37
Which type of pipelines collect the gas from the transmission system so utility companies can distribute the gas to end users?
- A. Midstream
- B. Distribution
- C. Gathering
- D. Transmission
Answer: B
NEW QUESTION # 38
Which is used to calibrate a pH meter?
- A. Distilled water
- B. Standard buffer solution
- C. Deionized water
- D. Standard solvent solution
Answer: B
NEW QUESTION # 39
Examples of non-ferrous metals include
Select All that Apply:
- A. iron
- B. mild steel.
- C. aluminum
- D. copper
Answer: C,D
NEW QUESTION # 40
The best choice of instrument for holiday testing of thick film concrete coatings is:
- A. High Voltage DC Constant Current
- B. High Voltage DC Pulse Type
- C. Low Voltage Sponge Type
- D. High Voltage AC
Answer: A
NEW QUESTION # 41
......
To be eligible for the NACE-CIP2-001 exam, candidates must have a minimum of two years of experience in coating inspection and pass the NACE-CIP1 exam. NACE-CIP2-001 exam consists of 100 multiple-choice questions, which must be completed within four hours. NACE-CIP2-001 exam is computer-based, and results are available immediately after completion.
NACE-CIP2-001 certification exam is a challenging exam that requires candidates to have a deep understanding of coating technology and inspection techniques. It is designed to test the knowledge and skills of experienced coating inspectors and ensure that they have the expertise needed to perform their jobs safely and effectively. NACE-CIP2-001 exam is administered by NACE International and is offered at various locations around the world. Candidates who pass the exam are awarded the NACE-CIP2-001 certification, which is a mark of excellence in the coating industry.
NACE-CIP2-001 Free Exam Files Downloaded Instantly: https://vcecollection.trainingdumps.com/NACE-CIP2-001-valid-vce-dumps.html
